Инструкция roland sp 540i

У нас вы можете скачать книгу инструкция roland sp 540i в fb2, txt, PDF, EPUB, doc, rtf, jar, djvu, lrf!

Installation Environment Temperature and Humidity Maintain the specified temperature and humidity even when the machine is not in use. Temperatures that are too high may degrade the ink and cause malfunction. Temperatures that are too low may cause the ink to freeze and damage the heads. Assembling and Installing Assembling the Stand First assemble the stand, then mount the machine on top of the stand.

Tighten the bolts securely. Loose bolts may cause the stand to wobble. Align with the arms. Install the stopper-attached shaft at the location closest to the back of the machine the location farthest from the front of the machine. Pass one end of the shaft through an arm, then move the other end of the shaft so that the machine and the shaft are parallel.

Use caution, because discharged fluid used in inspection may remain. Bottom plug It is needed when moving the machine, so do not discard it. Turn the bottle without applying excessive force. Store the packing materials carefully, because they are needed again when transporting the machine for relocation or the like. Remove the lower bolts. Assembling and Installing Removing the Packing Materials Tape and packing materials are attached to the machine to protect it from vibration during transportation.

When installation is complete, remove these. Remove all packing materials. Incorrect voltage or insufficient current may cause fire or electrical shock. This can prevent fire or electrical shock due to current leakage in the event of malfunction. Installing the Ink Cartridges Filling with Ink for the First Time Special procedures are required when installing ink cartridges for the first time. These are required only once, when installing ink cartridges for the first time after shipment from the factory.

You first clean the print heads using cleaning fluid, then fill with the inks of the various colors. Installing the Ink Cartridges Switch on the power and make the initial settings. Installing the Ink Cartridges Pull out the dummy cartridges from slots 3 and 4.

Insert the dummy cartridges into slots 1 and 2. Installing the Ink Cartridges Pull out the dummy cartridges from slots 1 and 2. Make sure the drain bottle is not overflowing with discharged fluid, then press Insert the ink cartridges for the respective colors. Sudden movement of the machine may cause injury. Doing so may result in injury, and the cutting performance of the blade will be impaired.

Installing the Blade Install the blade holder. Insert until the collar is flush with the surface. Screw Support it from below. Network Settings Introduction This machine has a built-in print server as a network interface. When you use the print server, you can send output data to the machine from anywhere on the network. The factory default for the time after which the machine switches to the sleep mode is 30 minutes. You can change the setting for the time of the shift to the sleep mode.

This section explains how to load media, using roll media as an example. For information on how to load sheet media, refer to the page indicated below. Be sure to ensure the media is within this range. Placing the pinch rollers inside each of the grit patterns ensures that they are positioned above the grit rollers. Be sure to place the left and right pinch rollers affixed with blue stickers at the edges of the media.

Make sure all areas of the media are taut. Left media clamps Right media clamps Line up the edge of the Line up the edge of the media with the centers of media with the centers of the holes. Make sure lights up. The cutoff location on the media is as shown in the figure below. Blade protector Blade protector The media is fed This machine is equipped with a media heating system that warms the media. You use this mainly to improve ink adhesion and dry the ink. You can adjust the temperature settings to match the type of media and the printing speed.

Print heater This heater is used mainly to improve ink adhesion. Use the following as a general guide and adjust accordingly. General Guide for Adjustment Print heater You use this mainly to improve ink adhesion and inhibit smudging. This procedure enables the machine to receive data from the computer and perform output. When printing data that includes cutting paths is received, you can also carry out cutting immediately after performing printing.

If dot drop-out occurs, perform cleaning. Replace with an item of identical type and color. This makes it unnecessary to run out media to the rear of the machine before the operation. Dispose of collected material before the bottle becomes full.

The message shown in the figure appears when a certain amount of discharged fluid has collected in the bottle. Follow the procedure below to discard the discharged fluid. The print heads are components that wear out. Periodic replacement is required depending on the frequency of use. Purchase them from your authorized Roland DG Corp. If you use up the cleaning kit, purchase a new one from your authorized Roland DG Corp. Be especially careful to clean away any fibrous dust lint.

Clean in the sequence shown in the figure below. Cleaning stick Be sure to clean using one of the included cleaning sticks. Never touch the nozzle surface. Use the included tweezers.

Detach the hook and pull up and out. Felt surface to- ward the rear Rubber surface toward the front Preparations are complete when this screen appears. Insert until the col- lar is flush with the surface. Tug the blade holder upward to make sure it does not come loose. Quit the blade replacement mode. Doing so may result in injury. Enter the blade replacement mode. The knife is secured in place by the magnet. Take care to ensure that the knife does not slip out of position at this time.

When you turn on the power, the machine automatically performs some operations such as those to keep the print heads from drying out. Allowing the machine to stand completely unused for a prolonged period may damage the print heads, so be sure to switch on the power to perform these automatic operations.

Description pauses printing and cutting. Align the center of the blade with the new output-start location. Move the height-adjustment lever to adjust the head height. High Low Standard Height-adjustment lever Choose the value that produces Test pattern the least misalignment.

Use to set the cor- rection value. Press Go back to the original screen. Press to go back to the original screen. Wmm Description The movement distance of media experiences subtle changes due to the thickness of the media and the temperature of the Go back to the original scr een. Press to go back to the original scr een. Description T he movement transfer of media experiences subtle changes due to the thic kness of the media and the temperature of the print heater.

Use to mak e the setting for the corr ection value. Press to enable the setting. Larger values produce progressi vely slower mo vement of the media, enabling you to extend the drying time accordingly. Use to set the value. T wo of these are installed when the mac hine is shipped from the factory.

Use to select "LONG. If roll media is loaded, then remov e the media first. Use to mak e the setting.

Pr ess to ex ecute. Use to select the print heater or the dryer. Use to select "OFF. Chapter 4 Feature Ref erence 81 Using the Cr op-mark F eature T o P erform Printing and Cutting Separately When you remov e printed media and then reload it and perform cutting, you carry out alignment to prev ent misalign- ment of the printing results and the cut lines. Aligning Manually and Cutting Depending on the type of media, it ma y not be possible to detect crop marks automatically.

About Align P oints T he numbers for align points are determined with reference to the location of the base point. Use to choose the cutting condition y ou want to set. Use to enter the value. T he blade should leav e faint traces on the backing paper. The blade trace is indistinct. Increase the blade force. The blade trace is too deep and cuts into the backing pa per. Ex ecute the [ENV. Press to ex ecute. Enter the adjustment value y ou read. Description T his drains the ink inside the printer and washes the interior using cleaning cartridges as a preliminary for moving the printer or conducting maintenance.

Pr ess to start printing. Description T his prints system information, including a list of setting values. T his makes it impossible to go on to the next operation unless you redo the setting for the amount remaining.

Carry out a printing test and make sure no dot drop-out occurs. If dot drop-out is present, perform head cleaning. T he following may cause ink to drip on the media during printing.

Fail- ure to do so ma y damage the print heads. This can cause such pr oblems as poor printing quality , contact with the media b y the print heads, misaligned positioning, or media jams.

Chapter 5 What to Do If 5. Make the guides at the edges of the print heads line up with the print heads at the edges of the cap unit. T urn the pipe further to bring the heads near the cap unit. When the heads make contact with the cap-unit, turn the pipe one or two more turns. They do not indicate any er ror. Follo w the prompts and tak e action accordingl y. If the action described here does not correct the pr oblem, or if an err or mes- sag e not described here appear , contact y our ven- dor or the nearest Roland DG Corp.

Maximum Ar ea When Using Cr op Marks When crop marks are used, the printing or cutting area is reduced from the maximum area by an amount equal to the crop marks. Chapter 6 Specifications About the Blade T he cutting conditions and the service life of the blade change according to the media and the operating environment, even when using identical blades.

T he service life also differs according to the type of blade. Chapter 6 Specifications Locations of the P o w er Rating and Serial Number Labels P o wer Rating Use an electrical outlet that meets the require- ments for voltage, frequenc y , and amperage given here.

Serial Number T his is required when y ou seek maintenance, servicing, or support. Важным пунктом после покупки устройства Roland SPV или даже перед его покупкой является прочтение его инструкции обслуживания.

Это необходимо сделать о нескольким простым причинам: Если вы еще не купил Roland SPV то сейчас хороший момент, чтобы ознакомиться с основными данными, касающимися изделия. Сначала просмотрите первые страницы инструкции, которую вы найдете выше. Вы должны там найти самые важные технические данные Roland SPV - таким образом вы проверите, выполняет ли оборудование Ваши требования.